Jeld-wen JII004 Aluminum Windows with Nail Fin User Manual download pdf (Page 1)

INSTALLATION INSTRUCTIONS

for Aluminum Windows with Nail Fin (JII004)

Newer construction methods have led to an increase in air and water

tightness in buildings. This frequently leads to negative air pressure

inside the home, which can draw water through very small openings.

Our installation method integrates the window with the weather

barrier of the structure (typically building wrap).

Thank you for selecting JELD-WEN products. Attached are JELD-WEN’s

recommended installation instructions for Aluminum windows with

an integral nail n. Not all window types may be installed into every

wall condition in all areas. Consult your local building code official

for applicable building codes and regulations. Local building code

requirements supersede recommended installation instructions. Areas

such as Florida and the Texas TDI region have different anchoring

requirements based on product certification. For information on specific

products, visit www.floridabuilding.org or www.tdi.texas.gov and

follow the anchoring schedule given in the drawings for the product

instead of the anchoring schedule in this document.

Please Note! Installations where the sill is higher than 35 feet above

ground level, or any product installation into a wall condition not

specifically addressed in these instructions, must be designed by an

architect or structural engineer. Failure to install windows into square,

level, and plumb openings could result in denial of warranty claims for

operational or performance problems.

Note to Installer: Provide a copy of these instructions to the building

owner. By installing this product, you acknowledge the terms and

conditions of the limited product warranty as part of the terms of

thesale.

GLOSSARY

Buck

A wood framework attached to the masonry inside a window or

patiodoor rough opening.

Mull Joint

The joint where two or more window units are structurally

joinedtogether.

Mulled Unit

Two or more window units structurally joined together.

Precast Sill

A pre-formed concrete block placed in the sill of a masonry/block wall to

support a window.

Shiplap

The layering method in which each layer overlaps the layer below it so

that water runs down the outside.

Weep Hole (weep channel)

The visible exit or entry part of a water drainage system used to drain

water out of a window.

IMPORTANT INFORMATION AND GLOSSARY

ROUGH OPENINGS

This installation guide specically addresses masonry/block wall,

sheathed wall and open-stud construction.

MASONRY/BLOCK WALL CONSTRUCTION

This installation assumes that

a framework of studs (often

called a buck) has already been

properly fastened and sealed to

the concrete/masonry wall by a

building professional.

FULLY SHEATHED WALL CONSTRUCTION

The wall framing is covered by sheathing. Windows will be mounted

ush against the sheathing. This installation assumes building wrap is

properly installed prior to installation.

Estimated Install

Time for New

Construction

First Time: 2 hrs

Experienced: 1.5 hrs

Professional:

1 hr

8 4

7 5

Buck

Sheathed Wall

OPEN-STUD CONSTRUCTION

If self-adhesive ashing is to be

applied so that it is wider than

the framing of the wall, it may

be necessary to cover the wall

with backing support sufcient

to support the entire width of

the ashing.

This backing support should be a

non water-degradable, thin (max.

1/8" thick) sheet material such

as vinyl sheeting. Completely

surround the rough opening with

the backing support. Backing support must be applied before building

wrap. The window will be mounted with the nailing n ush against

the applied backing support.

Trimmer

studs

Header

Sheathing

King

stud

1 2 3 4 5 6

Summary of Contents

Page 1 - ROUGH OPENINGS

INSTALLATION INSTRUCTIONSfor Aluminum Windows with Nail Fin (JII004)Newer construction methods have led to an increase in air and water tightness in b

Page 2 - MATERIALS AND TOOLS

INSTALLATION INSTRUCTIONSfor Aluminum Windows with Nailing Fin (JII004)2SAFETY• Read and fully understand ALL manufacturers’ instructions before begin

Page 3 - PREPARE BUCK

INSTALLATION INSTRUCTIONSfor Aluminum Windows with Nailing Fin (JII004)3REMOVE PACKAGINGRemove shipping materials such as corner covers, shipping bloc

Page 4 - INSTALL WINDOW

INSTALLATION INSTRUCTIONSfor Aluminum Windows with Nailing Fin (JII004)45. Place ashing on rough opening sill, wrapping the ashing up 6" on eac

Page 5 - INSTALL WINDOW - CONTINUED

INSTALLATION INSTRUCTIONSfor Aluminum Windows with Nailing Fin (JII004)5SECURE WINDOWAreas such as Florida and the Texas TDI region have different anc

Page 6 - COMPLETE INSTALLATION

INSTALLATION INSTRUCTIONSfor Aluminum Windows with Nailing Fin (JII004)6Please visit jeld-wen.com for warranty and care and maintenance information.Th

Comments to this Manuals

No comments

Jeld-wen JII004 Aluminum Windows with Nail Fin User Manual Page 1

Browse online or download User Manual for For Home Jeld-wen JII004 Aluminum Windows with Nail Fin. JELD-WEN JII004 Aluminum Windows with Nail Fin User Manual [de]

Summary of Contents

Comments to this Manuals

Jeld-wen JII004 Aluminum Windows with Nail Fin User Manual Page 1

Browse online or download User Manual for For Home Jeld-wen JII004 Aluminum Windows with Nail Fin. JELD-WEN JII004 Aluminum Windows with Nail Fin User Manual [de]

Summary of Contents

Comments to this Manuals

Related products and manuals for For Home Jeld-wen JII004 Aluminum Windows with Nail Fin